HEAT-SHRINK FILM 19µ thick 350mm x 600m roll

High quality PVC shrink film, 19µ thick and centre folded on the roll, so the film is actually twice as wide as the roll widths.
Works with most shrink wrap systems.

350mm x 600m roll.

HEAT-SHRINK FILM 19µ thick 450mm x 600m roll

High quality PVC shrink film, 19µ thick and centre folded on the roll, so the film is actually twice as wide as the roll widths.
Works with most shrink wrap systems.

450mm x 600m roll.

HEAT-SHRINK FILM 19µ thick 600mm x 600m roll

High quality PVC shrink film, 19µ thick and centre folded on the roll, so the film is actually twice as wide as the roll widths.
Works with most shrink wrap systems.

600mm x 600m roll.

HEAT-SHRINK FILM 19µ thick 750mm x 600m roll

High quality PVC shrink film, 19µ thick and centre folded on the roll, so the film is actually twice as wide as the roll widths.
Works with most shrink wrap systems.

750mm x 600m roll.

SILICONE FOAM STRIP 100mm x 915mm 2 pieces

Silicone foam strip for Magik Wand Cordless Shrink Wrapper.

The essential Silicone Foam underlay for sealing is positioned on any flat surface.
Efficiency is increased if you place two pieces in an 'L' layout.
100mm x 915mm, 2 pieces.

SILICONE FOAM STRIP 100mm x 915mm 1 piece

Silicone foam strip for Magik Wand Cordless Shrink Wrapper.

The essential Silicone Foam underlay for sealing is positioned on any flat surface.
Efficiency is increased if you place two pieces in an 'L' layout.
100mm x 915mm, 1 piece.

Magik Wand BASE HEATER UNIT+WAND 31"/785mm

MAGIK WAND Cordless Shrink Wrapper - Base Heater Unit + Wand 785mm / 31"

The unique Magik Wand Sealing Arm, 3648, is not connected to the base unit, so you can manoeuvre it any way you need on the bench.
It allows you to apply clear shrink-film protection to frames, mounted prints and posters on board.
The steel base Heater Unit, 3649, has a mains voltage heating element inside. When the Magik Wand is placed into it, it heats up. Wand stays hot more than long enough to seal a pack both ways, before it is returned to the base unit, where it quickly re-heats.

Magik Wand base heater unit takes 610mm / 24" and 785mm / 31" Wands. It has an adjustable temperature control.
Adjust the heating temperature to achieve a fine balance between sealing and cutting. It can take a little while to achieve this.

The rugged steel Film Roller Dispenser, 3451, with separator bar is 510mm / 20" wide, and takes film up to 762mm / 30". Carries the weight of a 600m roll of shrink film.
The essential Silicone Foam, 3423, underlay for sealing is positioned on any flat surface. Efficiency is increased if you place two pieces in an 'L' layout.
Apply occasional thin film of silicone grease to sealing edge of Wand.
You will need a hot air gun, 425.

Magik Wand is made in the UK, engineered to ISO 9002 and carries the CE mark. It requires a 240v, 5 amp supply. Some details of the design are copyright or subject of patent applications.
Magik Wand includes silicone grease.

FILM ROLLER / SEPARATOR for Magik Wand

Film Roller / Separator for Magik Wand Cordless Shrink Wrapper.

The rugged steel Film Roller Dispenser with separator bar is 510mm / 20" wide, and takes film up to 762mm / 30". Carries the weight of a 600m roll of shrink film.

Magik Wand WAND ONLY 610mm / 24"

MAGIK WAND Cordless Shrink Wrapper - Wand only, 610mm / 24"

The unique Magik Wand Sealing Arm, 3648, is not connected to the base unit, so you can manoeuvre it any way you need on the bench.
It allows you to apply clear shrink-film protection to frames, mounted prints and posters on board.
The steel base Heater Unit, 3649, has a mains voltage heating element inside. When the Magik Wand is placed into it, it heats up. Wand stays hot more than long enough to seal a pack both ways, before it is returned to the base unit, where it quickly re-heats.

Magik Wand base heater unit takes 610mm / 24" and 785mm / 31" Wands. It has an adjustable temperature control.
Adjust the heating temperature to achieve a fine balance between sealing and cutting. It can take a little while to achieve this.

The rugged steel Film Roller Dispenser, 3451, with separator bar is 510mm / 20" wide, and takes film up to 762mm / 30". Carries the weight of a 600m roll of shrink film.

The essential Silicone Foam, 3423, underlay for sealing is positioned on any flat surface.
Efficiency is increased if you place two pieces in an 'L' layout.
Apply an occasional thin film of silicone grease to sealing edge of Wand.
You will need a hot air gun, 425.

Magik Wand is made in the UK, engineered to ISO 9002 and carries the CE mark. It requires a 240v, 5 amp supply.
Some details of the design are copyright or subject of patent applications.

Magik Wand WAND ONLY 785mm / 31"

MAGIK WAND Cordless Shrink Wrapper - Wand only, 785mm / 31"

The unique Magik Wand Sealing Arm, 3648, is not connected to the base unit, so you can manoeuvre it any way you need on the bench.
It allows you to apply clear shrink-film protection to frames, mounted prints and posters on board.
The steel base Heater Unit, 3649, has a mains voltage heating element inside. When the Magik Wand is placed into it, it heats up. Wand stays hot more than long enough to seal a pack both ways, before it is returned to the base unit, where it quickly re-heats.

Magik Wand base heater unit takes 610mm / 24" and 785mm / 31" Wands. It has an adjustable temperature control.
Adjust the heating temperature to achieve a fine balance between sealing and cutting. It can take a little while to achieve this.

The rugged steel Film Roller Dispenser, 3451, with separator bar is 510mm / 20" wide, and takes film up to 762mm / 30". Carries the weight of a 600m roll of shrink film.

The essential Silicone Foam, 3423, underlay for sealing is positioned on any flat surface.
Efficiency is increased if you place two pieces in an 'L' layout.
Apply an occasional thin film of silicone grease to sealing edge of Wand.
You will need a hot air gun, 425.

Magik Wand is made in the UK, engineered to ISO 9002 and carries the CE mark. It requires a 240v, 5 amp supply.
Some details of the design are copyright or subject of patent applications.

Magik Wand BASE HEATER UNIT

MAGIK WAND Cordless Shrink Wrapper - Base Heater Unit

The unique Magik Wand Sealing Arm, 3648, is not connected to the base unit, so you can manoeuvre it any way you need on the bench.
It allows you to apply clear shrink-film protection to frames, mounted prints and posters on board.
The steel base Heater Unit, 3649, has a mains voltage heating element inside. When the Magik Wand is placed into it, it heats up. Wand stays hot more than long enough to seal a pack both ways, before it is returned to the base unit, where it quickly re-heats.

Magik Wand base heater unit takes 610mm / 24" and 785mm / 31" Wands. It has an adjustable temperature control.
Adjust the heating temperature to achieve a fine balance between sealing and cutting. It can take a little while to achieve this.

The rugged steel Film Roller Dispenser, 3451, with separator bar is 510mm / 20" wide, and takes film up to 762mm / 30". Carries the weight of a 600m roll of shrink film.

The essential Silicone Foam, 3423, underlay for sealing is positioned on any flat surface.
Efficiency is increased if you place two pieces in an 'L' layout.
Apply an occasional thin film of silicone grease to sealing edge of Wand.
You will need a hot air gun, 425.

Magik Wand is made in the UK, engineered to ISO 9002 and carries the CE mark. It requires a 240v, 5 amp supply.
Some details of the design are copyright or subject of patent applications.

HEAT-SHRINK FILM 19µ thick 250mm x 600m roll

High quality PVC shrink film, 19µ thick and centre folded on the roll, so the film is actually twice as wide as the roll widths.
Works with most shrink wrap systems.

250mm x 600m roll.

SILICONE GREASE M494 50gm Tube

Silicone grease for Magik Wand Cordless Shrink Wrapper.

Apply an occasional thin film of silicone grease to sealing edge of Wand.
50gm.

HEAT SHRINK GUN 2kW 230v

Heat Shrink Gun for Magik Wand Cordless Shrink Wrapper. 2kW, 230v.

HEAT-SHRINK FILM 38µ thick 450mm x 300m roll

High quality PVC shrink film, 19µ thick and centre folded on the roll, so the film is actually twice as wide as the roll widths.
Works with most shrink wrap systems.

450mm x 300m roll.

HEAT-SHRINK FILM 38µ thick 600mm x 300m roll

High quality PVC shrink film, 19µ thick and centre folded on the roll, so the film is actually twice as wide as the roll widths.
Works with most shrink wrap systems.

600mm x 300m roll.